Kurumun Atıf Alan Makalesi
Atıf Alan Yayın
Investigation of progressive tool wear for determining of optimized machining parameters in turning
Scopus
Toplam 177 atıf DOI
On-line monitoring of tool wear and tool breakage are very important to reduce production costs through the optimization of machining parameters. Increasing cutting forces affect workpiece quality and tool condition that is the ultimate aim of production line and progressive tool wear which can trigger the tool breakage. Taguchi method is extensively used for determining number of experiment while variance analysis (ANOVA) deals with which parameter/s is/are effective on output. This study contains experiments and optimization processes during turning of AISI 1050 material with 3 input parameters (cutting speed, feed rate, tool tip) using Taguchi method. In order to determine the condition of the cutting tool, measurement of tangential cutting force and acoustic emission (AE) were carried out during metal removing. ANOVA results showed that cutting speed is the most effective about %45 and tool tip is the second about %35 on tool wear. On the other hand, the effect of feed rate on tangential cutting force (%88) and cutting speed on AE (%80) is remarkably higher than the other two parameters. In order to obtain the minimum tool wear value, the optimum cutting parameters have been selected as v 1 = 135 m/min, f 2 = 0,214 mm/rev, T 2 = P25. By implemented sensor system tool breakage can be successfully detected and used for producing high quality materials with low costs.
Atıf Kaynağı
Atıf Yapan Yayın
Tribological aspects, optimization and analysis of cu-b-crc composites fabricated by powder metallurgy
Scopus
Havuzumuzda Open Access 56 atıf almış
Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-rein-forcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.
Atıf Yapan Makale Bilgileri
Kurumlar (5)
Bingöl Üniversitesi
Bingol, Turkey
Inönü Üniversitesi
Malatya, Turkey
Selçuk Üniversitesi
Selçuklu, Turkey
South Ural State University
Chelyabinsk, Russian Federation
University of Portsmouth
Portsmouth, United Kingdom